View NCP10006_1287687.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP100 Sub 1.0 V Precision Adjustable Shunt Regulator
The NCP100 is a precision low voltage shunt regulator that is programmable over a voltage range of 0.9 V to 6.0 V. This device features a guaranteed reference accuracy of 1.7% at 25C and 2.6% over the entire temperature range of -40C to 85C. The NCP100 exhibits a sharp low current turn-on characteristic with a low dynamic impedance of 0.20 W over an operating current range of 100 mA to 20 mA. These characteristics make this device an ideal replacement for zener diodes in numerous application circuits that require a precise low voltage reference. When combined with an optocoupler, the NCP100 can be used as an error amplifier for controlling the feedback loop in isolated low output voltage (2.3 V) switching power supplies. This device is available in TO-92 and in an economical space saving TSOP-5 package.
Features http://onsemi.com
TO-92 (TO-226) LP SUFFIX CASE 029 Pin 1. Reference 2. Anode 3. Cathode
3
1
2
5 1
TSOP-5 SN SUFFIX CASE 483
* * * * * * * * * * *
Programmable Output Voltage Range of 0.9 V to 6.0 V Voltage Reference Tolerance of 1.7% Sharp Low Current Turn-ON Characteristic Low Dynamic Output Impedance of 0.2 W from 100 mA to 20 mA Wide Operating Current Range of 80 mA to 20 mA TO-92 and Space Saving TSOP-5 Package Pb-Free Package is Available Reference for Single Cell Alkaline, NiCD and NiMH Applications Low Output Voltage (2.3 V) Switching Power Supply Error Amp Battery Powered Consumer Products Portable Test Equipment and Instrumentation
Cathode (K) Cathode (K) Reference (R) 0.7 V Anode (A)
PIN CONNECTIONS AND MARKING DIAGRAM
NC Anode Cathode 1 2 3 5 Anode RABAYWG G (Top View) RAB = Device Code A = Assembly Location Y = Year W = Work Week G = Pb-Free Package
4 Reference
Applications
XXXXX XXXXX ALYWWG G
Reference (R)
XXXXX = Specific Device Code A = Assembly Location L = Wafer Lot Y = Year WW = Work Week G = Pb-Free Package (Note: Microdot may be in either location)
ORDERING INFORMATION
Anode (A)
Figure 1. Symbol
Figure 2. Representative Block Diagram
Device NCP100SNT1 NCP100SNT1G NCP100ALPRPG
Package TSOP-5 TSOP-5 (Pb-Free) TO-92 (Pb-Free)
Shipping 3000 / Tape & Reel 3000 / Tape & Reel 2000 / Ammo Pack
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
(c) Semiconductor Components Industries, LLC, 2006
1
November, 2006 - Rev. 10
Publication Order Number: NCP100/D
NCP100
MAXIMUM RATINGS (TA = 25C, unless otherwise noted.)
AAAA A A A AAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A
Cathode to Anode Voltage (Note 1) VKA IK 7.0 V Cathode Current Range, Continuous (Note 2) -20 to 25 mA mA Reference Input Current Range, Continuous (Note 1) Thermal Resistance LP Suffix, TO-92 Package Thermal Resistance, Junction-to-Ambient Thermal Resistance, Junction-to-Lead SN Suffix, TSOP-5 Package Thermal Resistance, Junction-to-Ambient Operating Junction Temperature Range Storage Temperature Range IREF -0.05 to 2.0 C/W RqJA Rpsi-J-Anode lead RqJA TJ Tstg 168 32 225 -40 to 125 -65 to 150 C C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 4000 V per JESD-22, Method A114B. Machine Model Method 400 V. 2. The maximum package power dissipation limit must not be exceeded. TJ(max) * TA PD + RqJA
Rating
Symbol
Value
Unit
RECOMMENDED OPERATING CONDITIONS
AAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A
Cathode-to-Anode Voltage Range (Note 3) Cathode Current Range VKA IK 0.9 0.1 6.0 20 V mA 3. Valid device operation is not guaranteed if Vka is allowed to fall below 0.875 V at any time over the operating temperature range of -40C to +85C.
Condition
Symbol
Min
Max
Unit
http://onsemi.com
2
NCP100
ELECTRICAL CHARACTERISTICS (TA = 25C, unless otherwise noted.)
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AA A A A A AAA A A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAA AAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A A A AAAAA AA AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAA
Reference Voltage (IKA = 10 mA, Figure 3) VKA = 0.9 V TA = 25C TA = 0C to 70C TA = -40C to 85C VKA = 1.0 V TA = 25C TA = 0C to 70C TA = -40C to 85C VREF V 0.684 0.682 0.678 0.686 0.684 0.680 - 0.696 - - 0.698 - - 1.0 0.708 0.710 0.714 0.710 0.712 0.716 12 Reference Input Voltage Change Over Temperature VKA = 1.0 V, IK = 10 mA, TA = -40C to 85C, Figure 3 (Notes 4, 5) DVREF mV mV Reference Input Voltage Change Over Programmed Cathode Voltage (IK = 10 mA, Figure 3) VKA = 0.9 V to 1.0 V VKA = 1.0 V to 6.0 V Regline -5.0 0 - 0.2 6.7 1.3 5.0 12 2.4 Ratio of Reference Input Voltage Change to Cathode Voltage Change VKA = 0.9 V to 6.0 V, IK = 10 mA, Figure 3 Reference Input Current (VKA = 1.0 V, IK = 10 mA) Minimum Cathode Current for Regulation DVREF DVKA IREF mV/V -100 - - - -30 80 70 100 - nA mA mA W IK(min) IK(off) |ZKA| Cathode Off-State Current (VKA = 6.0 V, VREF = 0 V) 90 - Dynamic Output Impedance VKA = 1.0 V, IK = 100 mA to 20 mA, f v 1.0 kHz, Figure 3 0.2 4. Low duty cycle pulse techniques are used during testing to maintain the junction temperatures as close to ambient as possible. 5. The DVREF parameter is defined as the difference between the maximum and minimum values obtained over the ambient temperature range of -40C to 85C. VREF (max) DVREF = VREF (max) - VREF (min) DTA = T2 - T1 VREF (min) T1 T2 AMBIENT TEMPERATURE
Characteristic
Symbol
Min
Typ
Max
Unit
http://onsemi.com
3
NCP100
1.0 k Vin IK VKA Vin
1.0 k VKA IK + 22 mF
R1
+ CL
10 k
100 k
VREF
R2
VREF
Figure 3. General Test Circuit
Figure 4. Test Circuit for Reference Input Voltage Change vs. Cathode Voltage
110 k IK VKA CL + + 22 mF 100 k 0.1 mF 0.01 mF Input +
1.0 k Output IK R1
50 k
R1
100 k
Figure 5. Test Circuit for Dynamic Impedance vs. Frequency
Figure 6. Test Circuit for Spectral Noise Density
REFERENCE INPUT VOLTAGE CHANGE (%)
1.0 VKA = 0.9 V
CATHODE VOLTAGE CHANGE (%)
IK = 250 mA f v 1.0 kHz CL = 22 mF Figure 3 VKA = 1.0 V
2.0
1.0
VKA = 0.9 V
IK = 250 mA f v 1.0 kHz CL = 22 mF Figure 3 VKA = 1.0 V
0
0 VKA = 6.0 V
VKA = 6.0 V
-1.0
VKA = 0.9 V
VKA = 6.0 V -2.0 -50 -25 0 25 50 75 100 125
-1.0 -50
-25
0
25
50
75
100
125
TA, TEMPERATURE (C)
TA, TEMPERATURE (C)
Figure 7. Reference Input Voltage Change vs. Ambient Temperature
Figure 8. Cathode Voltage Change vs. Ambient Temperature
http://onsemi.com
4
NCP100
20 IK, CATHODE CURRENT (mA) 15 10 5.0 0 -5.0 -10 -0.8 -0.6 -0.4 -0.2 IK, CATHODE CURRENT (mA) VKA = 1.0 V CL = 3.3 mF TA = 25C Figure 3 200 150 100 50 0 -50 VKA = 1.0 V CL = 3.3 mF TA = 25C Figure 3
IK(min)
0
0.2
0.4
0.6
0.8
1.0
1.2
-100 -0.6 -0.4
-0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
VKA, CATHODE VOLTAGE (V)
VKA, CATHODE VOLTAGE (V)
Figure 9. Cathode Current vs. Cathode Voltage
Figure 10. Cathode Current vs. Cathode Voltage
DVREF, REFERENCE INPUT VOLTAGE CHANGE (mV)
8.0 |ZKA|, DYNAMIC IMPEDANCE (W) IK = 10 mA CL = 22 mF TA = 25C Figure 4
10 VKA = 1.0 V IK = 9.5 mA to 10.5 mA CL = 3.3 mF TA = 25C Figure 5
6.0
1.0
4.0
0.1
2.0
0 0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
0.01 1.0
10
100 FREQUENCY (Hz)
1.0k
10k
VKA, CATHODE VOLTAGE (V)
Figure 11. Reference Input Voltage Change vs. Cathode Voltage
Figure 12. Dynamic Impedance vs. Frequency
50 GAIN AV, VOLTAGE GAIN (dB) 30
120 EXCESS PHASE () VREF, REFERENCE VOLTAGE (mV)
706
60 PHASE
700
TA = -40C = 25C
10
0
694
-10
VKA = 1.0 V IK = 10 mA TA = 25C 100 1.0k 10k 100k
-60
688
= 70C = 85C = 105C
f 1.0 kHz CL = 3.3 mF Figure 3 200 250 300
-30 10
-120 1.0 M
682 50 100 150 IK, CATHODE CURRENT (mA)
FREQUENCY (Hz)
Figure 13. Small-Signal Voltage Gain and Phase vs. Frequency
Figure 14. Reference Voltage vs. Cathode Current for VKA = 0.9 V
http://onsemi.com
5
NCP100
698 VREF, REFERENCE VOLTAGE (mV) TA = -40C VREF, REFERENCE VOLTAGE (mV) 708 = 105C 704
697 = 25C = 70C = 85C = 105C f 1.0 kHz CL = 3.3 mF Figure 3 696 50 100 150 200 250 300
700 = 70C = 85C 696 = 25C TA = -40C f 1.0 kHz CL = 22 mF Figure 3 200 250 300
692 50
100
150
IK, CATHODE CURRENT (mA)
IK, CATHODE CURRENT (mA)
Figure 15. Reference Voltage vs. Cathode Current for VKA = 1.0 V
Figure 16. Reference Voltage vs. Cathode Current for VKA = 6.0 V
714 VREF, REFERENCE VOLTAGE (mV) 710 = 25C 706 702 698 694 690 0 TA = -40C f 1.0 kHz Figure 3 CL = 22 mF 4.0 6.0 = -40C = 85C = 70C = 105C
1000 NOISE VOLTAGE (nV/pHz) VKA = 1.0 V IK = 10 mA CL = 3.3 mF TA = 25C Figure 6
800
600
400
200
2.0
0 10
100
1.0 k FREQUENCY (Hz)
10 k
100 k
VKA, CATHODE VOLTAGE (V)
Figure 17. Reference Voltage vs. Cathode Current
Figure 18. Spectral Noise Density
6.0 VKA, CATHODE VOLTAGE (V) 5.0 4.0 3.0 2.0 1.0 NON-OPERATIONAL 0 1.0 10 CL, LOAD CAPACITANCE (mF) 100 0 200 400 600 800 1000 1200 1400 1600 t, TURN-ON TIME (ms) STABLE OPERATION VIN (V) 0 2.0 0 VKA (V) UNSTABLE OPERATION IK = 0.08 mA to 30 mA CESR 4.0 W TA = -40C to 85C 1.0 IK = 10 mA CL = 3.3 mF TA = 25C
0.5
Figure 19. Stability Boundary Conditions
Figure 20. Turn-On Time
http://onsemi.com
6
NCP100
APPLICATIONS INFORMATION The NCP100 is an adjustable shunt regulator similar to the industry standard 431-type regulators. Each device is laser trimmed at wafer probe to allow for tight reference accuracy and low reference voltage shift over the full operating temperature range of -40C to +85C (Figure 7). The nominal value for the reference is 0.698 V. This lower voltage allows the device to be used in low voltage applications where the traditional 1.25 V and 2.5 V references are not suitable.
Rin Vin IK CL R2 VREF VKA LOAD
In Figure 21, the input resistor (Rin) is nominally set to 1.0 kW. For proper operation, once Vin, R1 and R2 are set, the resistance and power value of Rin can be determined by the following equation.
Rin + Vin * VKA VKA IK ) IL ) R )R
1 2
R1
The maximum current that will flow through Rin must be determined. This is the sum of the maximum values of cathode current, resistor divider network current, and load current. With Vin, set, the difference (Vin-VKA) is now constant. This value is divided by the maximum current calculated above to arrive at the value of Rin. Once the value of Rin is calculated, it's minimum power rating is easily derived by:
Pin + (Iin)2 Rin
Figure 21. Typical Application Circuit
The typical application circuit for this device is shown in Figure 21. The cathode voltage can be programmed between 0.9 V to 6.0 V to allow for proper operation by setting the R1/R2 resistor divider network values. The following equation can be used in calculating the cathode voltage (VKA). Note, if VKA is known then the ratio of R1 and R2 can be determined from this equation as well.
VKA + VREF 1 ) R1 ) IREF R1 R2
The table below shows the required R1/R2 values using 1.0% resistors for commonly used voltages.
VKA (V) 0.9 1.0 1.8 3.3 5.0 6.0 R1 (kW) 30 R2 (kW) 100 100 100 100 100 100
Once these values are determined, it should be verified that the minimum and maximum values of IK are within the recommended range of 0.1 mA to 20 mA under the worst case conditions. For stability, the NCP100 requires an output capacitor between the cathode and anode. Figure 19 shows the capacitance boundary values required for stable operation across the -40C to 85C temperature range. The goal is to remain to the right of the curve for any programmed cathode voltages. For example, if the VKA is programmed to 1.0 V, then a load capacitor value of 3.0 mF or greater would be selected. The load capacitor's Equivalent Series Resistance, ESR, should be less than 4.0 W. Both the capacitance and ESR values should be checked across the anticipated application temperature range to insure that the values meet the requirements stated above.
Vin
1.0 k
Iin
AAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA A A AAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A AAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAA AAAAAAAAAAAA A
43.2 158 374 619 750
Vcomp R1
Rcomp VKA IK + CL
100 k
VREF
Because the error amplifier is a CMOS design the value of IREF is extremely low allowing it to be neglected for most applications. The low IREF also allows for higher R1 and R2 values keeping current consumption very low. The NCP100 is especially well suited for lower voltage applications, particularly at VKA = 1.0 V. As is seen in Figures 7 and 8, this device exhibits excellent cathode and reference voltage flatness across the -40C to +85C temperature range.
Figure 22. Negative Dynamic Impedance Circuit
One unique use for the NCP100 is that it can be configured for negative dynamic impedance as shown in Figure 22. This circuit is equivalent to Figure 21 with the addition of a small value resistor Rcomp in the cathode circuit. The regulated voltage output remains across the NCP100 cathode and anode leads. The voltage programming and stability requirements remain the same as in the typical application shown in Figure 21.
http://onsemi.com
7
NCP100
The circuit performs the same as the one in Figure 21 with the exception of the effects of Rcomp. As IK increases, the voltage across Rcomp also increases by:
Vcomp + IKA Rcomp
Vcomp effectively adjusts the NCP100 programmed VKA voltage slightly down since the R1/R2 voltage divider will try to hold the point it is connected to at the programmed voltage. The regulator VKA will now be lowered by the value of the Vcomp. This effect can compensate for the NCP100's intrinsic positive impedance versus cathode current (IK) to allow for 0 W or even a negative dynamic impedance.
Figure 23 shows this phenomenon for a program voltage of 1.0 V. The NCP100 intrinsic positive dynamic impedance response is the Rcomp = 0 W curve. A 0 W dynamic impedance regulator response is realized with Rcomp = 0.15 W. Negative dynamic impedance responses are achieved with Rcomp u 0.15 W. Figure 24 shows the characteristic at a programmed VKA of 6.0 V. The 0 W dynamic impedance value corresponds to Rcomp = 2.9 W. Figure 25 shows the dynamic impedance versus cathode compensation resistance for programmed voltages of 1.0 V, 3.3 V and 6.0 V. It can be seen that any value up to the positive intrinsic dynamic impedance of the NCP100 can be realized. The other limit is that with a high enough negative dynamic impedance, the NCP100 V may drop below the minimum operating VKA voltage of 0.9 V, which can result in unpredictable performance.
20 = 2.9 W = 1.5 W =0W 10 Rcomp= 5.8 W 5.0 IK = 0.1 to 20 mA TA = 25 C Figure 22 5.96 5.98 6.00 6.02 Rcomp W 0 1.5 2.9 4.4 5.8 6.04 |ZKA| W 2.9 1.4 0 -1.6 -2.9 6.06
20 IK, CATHODE CURRENT (mA)
Rcomp= 3.1 W
= 1.5 W = 0.15 W IK, CATHODE CURRENT (mA)
= 4.4 W 15
15 =0W 10 Rcomp (W) 0 0.15 1.5 3.1 |ZKA| (W) 0.2 0 -1.4 -1.6 IK = 0.1 mA to 20 mA TA = 25 C Figure 22 0 0.94 0.95 0.96 0.97 0.98 0.99 1.00 1.01
5.0
0 5.94
VKA, CATHODE VOLTAGE (V)
VKA, CATHODE VOLTAGE (V)
Figure 23. Cathode Current vs. Cathode Voltage for Programmed VKA = 1.0 V
Figure 24. Cathode Current vs. Cathode Voltage for Programmed VKA = 6.0 V
3.0 |ZKA|, DYNAMIC IMPEDANCE (W) 2.0 = 6.0 V 1.0 0 -1.0 VKA= 1.0 V -2.0 -3.0 0 = 3.3 V IK = 1.0 mA to 20 mA f 1.0 kHz Figure 22 TA = 25 C
1.0
2.0
3.0
4.0
5.0
Rcomp, CATHODE COMPENSATION RESISTANCE (W)
Figure 25. Dynamic Impedance vs. Cathode Compensation Resistance
http://onsemi.com
8
NCP100
Rin R1
Vin
Vout
Vin R1
Vout
R2
R2 V out + 1 ) R1 V R2 REF
V out +
1 ) R1 V R2 REF
V out min + 0.9 V ) V be
V out min + V REF
Figure 26. High Current Shunt Regulator
Figure 27. Low Dropout Series Pass Regulator
AC Line Input
1/2 Opto
R1 Isolated DC Output
NCP 100 - + UC3842
R2 -
1/2 Opto
Minimum Vout = (0.9 + 1.4) = 2.3 V
+ S
Q - + - +
R
Figure 28. Offline Converter with Isolated DC Output
The circuit in Figure 28 uses the NCP100 as a compensated amplifier for controlling the feedback loop of an isolated output line powered converter. This device allows the converter to directly regulate the output voltage at a significantly lower level than obtainable with the
common TL431 device family. The output voltage is programmed by the resistors R1 and R2. The minimum regulated DC output is limited to the sum of the lowest allowable cathode to anode voltage (0.9 V) and the forward drop of the optocoupler light emitting diode (1.4 V).
http://onsemi.com
9
+ - +
NCP100 TO-92 EIA RADIAL TAPE ON REEL
H2A H2A H2B H2B
H W2 H4 H5 L1 L F1 P2 P1 P H1 W1 W T T2 F2 P2 D T1
Figure 29. Device Positioning on Tape
Specification Inches Symbol
D D2 F1, F2 H H1 H2A H2B H4 H5 L L1 P P1 P2 T T1 T2 W W1 W2
Millimeter Max Min
3.8 0.38 2.4 1.5 8.5 0 0 18 15.5 8.5 2.5 12.5 5.95 3.55 0.15 -- 0.35 17.5 5.5 .15
Item Tape Feedhole Diameter Component Lead Thickness Dimension Component Lead Pitch Bottom of Component to Seating Plane Feedhole Location Deflection Left or Right Deflection Front or Rear Feedhole to Bottom of Component Feedhole to Seating Plane Defective Unit Clipped Dimension Lead Wire Enclosure Feedhole Pitch Feedhole Center to Center Lead First Lead Spacing Dimension Adhesive Tape Thickness Overall Taped Package Thickness Carrier Strip Thickness Carrier Strip Width Adhesive Tape Width Adhesive Tape Position
Min
0.1496 0.015 0.0945 .059 0.3346 0 0 0.7086 0.610 0.3346 0.09842 0.4921 0.2342 0.1397 0.06 -- 0.014 0.6889 0.2165 .0059
Max
4.2 0.51 2.8 4.0 9.5 1.0 1.0 19.5 16.5 11 -- 12.9 6.75 3.95 0.20 1.44 0.65 19 6.3 0.5
0.1653 0.020 0.110 .156 0.3741 0.039 0.051 0.768 0.649 0.433 -- 0.5079 0.2658 0.1556 0.08 0.0567 0.027 0.7481 0.2841 0.01968
NOTES: 1. Maximum alignment deviation between leads not to be greater than 0.2 mm. 2. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm. 3. Component lead to tape adhesion must meet the pull test requirements. 4. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. 5. Hold down tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 6. No more than 1 consecutive missing component is permitted. 7. A tape trailer and leader, having at least three feed holes is required before the first and after the last component. 8. Splices will not interfere with the sprocket feed holes.
http://onsemi.com
10
NCP100
PACKAGE DIMENSIONS
TO-92 (TO-226) CASE 29-11 ISSUE AL
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --- 0.250 --- 0.080 0.105 --- 0.100 0.115 --- 0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --- 6.35 --- 2.04 2.66 --- 2.54 2.93 --- 3.43 ---
A R P L
SEATING PLANE
B
K
XX G H V
1
D J C SECTION X-X N N
DIM A B C D G H J K L N P R V
http://onsemi.com
11
NCP100
PACKAGE DIMENSIONS
TSOP-5 SN SUFFIX PLASTIC PACKAGE CASE 483-02 ISSUE C
D
5 1 2 4 3
S
B
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. A AND B DIMENSIONS DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MILLIMETERS INCHES DIM MIN MAX MIN MAX A 2.90 3.10 0.1142 0.1220 B 1.30 1.70 0.0512 0.0669 C 0.90 1.10 0.0354 0.0433 D 0.25 0.50 0.0098 0.0197 G 0.85 1.05 0.0335 0.0413 H 0.013 0.100 0.0005 0.0040 J 0.10 0.26 0.0040 0.0102 K 0.20 0.60 0.0079 0.0236 L 1.25 1.55 0.0493 0.0610 M 0_ 10 _ 0_ 10 _ S 2.50 3.00 0.0985 0.1181
L G A J C 0.05 (0.002) H K M
SOLDERING FOOTPRINT*
1.9 0.074
0.95 0.037
2.4 0.094 1.0 0.039 0.7 0.028
SCALE 10:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
12
NCP100/D

▲Up To Search▲

Price & Availability of NCP10006

	To Download NCP10006 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .